Step Plumbing Guide for Bathtub Installation
Step Plumbing Guide for Bathtub Installation
Blog Article
What are your opinions on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably hard task. If the old tub is conveniently available, the task can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the task and also fit trying it. As opposed to employing a service provider to take over a halfway-completed job, it is much better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will help you install a brand-new bath tub in your restroom if you have already gotten a brand-new bathtub and also do not require to alter the arrangement of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
Getting ready for the Installment
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome due to the limited access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub till the level checks out degree.
To mount taps, fit all-time low of the outermost adaptable tap connector to the proper supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the bath tub and also examine the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub ought to wait up until the tub has been used at least when as this will settle it into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin making certain that the washers remain in location between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind ought to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently offered on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our section about Installing A Bathtub. Thank you for taking time to read through our article. Enjoyed reading our article? Please share it. Let others find it. I am grateful for your time. Please visit our site back soon.
Secure timely emergency plumbing assistance. Report this page